Saturday, 7 November 2020

Transom Skirt Trim | Making & Fitting The Upper Laminate

I made the upper laminate while the lower one was curing on the boat.

As with the lower one the manual tells us to use a table saw to cut a 30 degree bevel to make the upper laminate.

And again in the absence of a table saw, the upper piece was  marked up and planed to the required section.

The manual also states that the upper laminate will be easier to bend into place than the lower. A test bend by hand quickly demonstrated that this was not to be the case with my trim.

Perhaps it was the relatively stiff Sapele which I am using. In the manual it looks like the builder is using softwood.

Anyway, I used plenty of temporary screws driven into the lower laminate to pull the upper piece into place for a test fit, as here.


In this pic I am using a long sliding clamp to hold the starboard end in place, with a sawhorse holding the clamp against the hull to stop it springing off.

I label everything to avoid confusion about which face is which, like this.


As with the lower laminate, a secondary bevel was required at each end of the upper piece where it lands on the seatback top.

I was a bit over enthusiastic with the plane on the port secondary bevel, so I filled the small gap with a couple of slivers of Sapele. No problem. 

Here is a view from port of the upper laminate permanently glued in place.


A sliding clamp was necessary at each end to hold them snugly down while curing.

When well and truly cured I cleaned up the trim piece with the jack and block planes, as here.


I used a bevel gauge to make sure that the top of the trim was flat and even all across the stern, like this.


A good chisel was useful for finely paring the ends to shape, as here.


This is a view from starboard of the finished trim piece, sanded and rounded over.


It adds strength to the top of the transom as well as looking good.

This is what the starboard end of the upper laminate looks like, where it lands on the seatback top.


That's the transom skirt finished.

The next task is to cover the whole upper hull with fibreglass cloth - should be fun!


Transom Skirt Trim | Making & Fitting The Lower Laminate

The next task was to make the transom skirt trim, which fits along the top of the transom skirt on the stern and provides a solid edge and handhold as well as looking nice.

A 'grace note for PocketShip', as the manual describes it.

It looked pretty fiddly in the build instructions, but it would at least be a proper woodworking project for a change!

The trim piece is fashioned from Sapele hardwood and consists of two parts - an upper and a lower laminate which fit together as shown in this profile diagram on page 177 of the manual.



The lower laminate is fitted first. It is cut from 3/4" x 3/4" stock.

The manual tells us to set the table saw to 60 degrees to cut the required bevel, which of course I do not have.

If I could I would have a band saw and a table saw to hand, but there is simply no room in the workshop and I don't know anyone who possesses such things!

So I made a pattern for the 60 degree bevel, as here.


And then I marked up the Sapele stock and planed it to the required profile, as here.


The piece of wax candle on the bench is used to lubricate the sole of the plane when working on hard or difficult grain, and makes it very much easier.

Next I marked up a piece of scrap and planed it to the correct section, and then carefully planed the secondary bevel where the curved lower laminate lands on the seatback top.

Here is the scrap wood pattern.


And here it is clamped in place for a test fit.


It was a perfect fit, so the secondary bevel was then carefully marked up and planed on the lower laminate itself.

The piece was then clamped in place on the transom skirt for a test fit, as in this pic.


That went well. It bent into place with ease and plenty of spring clamps held it in place with a G clamp at each side to hold the bevelled ends in place.

I didn't take a pic but there is a single temporary screw holding the laminate in place in the centre of the skirt, to help with accurate fitting.

As an aside, you can see that I have applied a second layer of epoxy to the transom skirt fillet, although it is not yet sanded.

Here is a close up of the bevelled end where it lands on the port seatback top.


Finally, the lower laminate was glued permanently in place, as shown here viewed from the port side.


As another aside, you can see that the transom skirt fillet has been sanded and taped up for a final fairing layer of epoxy.

Lastly here is the lower laminate in place, with clamps removed and cleaned up.

The final fairing layer has also been applied to the transom skirt fillet.


This is what the  starboard end of the laminate looks like where it lands on the seatback top.


Looking nice. So far, so good!


Portlights | Decision Time

I have been thinking about portlights for some time, having seen some really nice stainless steel ones on other builders' blogs.

I'm not too keen on the simple acrylic deadlights supplied as standard. They look rather dull and don't open for ventilation.

The portlights which I favour are made by Vetus and have a 125mm cut out for fitting, which is slightly smaller than the cut out for the acrylic deadlights. It's the Vetus PQ51, and they look great! Expensive, but great.

So I would need to fill in the channel which is pre-routed for the cut out on the cabin topside panel before covering it with 'glass cloth.

I went ahead and did so. I can always cut out the opening as intended by the designer if I decide to stick with the acrylic deadlights.

Here is the starboard topside, with the channel filled in.


And here is the port side.


That was easy!


Rounding Over The Edges

It would soon be time to cover the upper hull in fibreglass cloth, so in anticipation of this I rounded over the edges of all the panels.

A sanding block and a piece of P80 grit sandpaper proved sufficient to the task. I sanded until the round over looked  as if a sheet of 'glass cloth would wrap smoothly round it, and no more.

Here is the port Dorade box, viewed from the bow.


And this is the starboard seatback where it meets the rear cabin wall and the cabin roof.


And lastly here is a view of the forward deck topside panel on the port side.


That was quick and easy, for a change!

Monday, 12 October 2020

Cleaning Up The Transom!

The installation of the transom is lost in the mists of time now, but when I did it I made a bit of a mess with squeezed out epoxy on the outside of the transom panel.

The hull side and topside panels also projected very slightly beyond the transom, and would need to be trimmed at some point.

My intention is to have a bright finish on the transom. That dark hardwood veneer will look great varnished, and it will be the only part of the hull to be finished that way.

So I had to be very careful not to scar the transom when cleaning it up.

Having had lots of practice in trimming the cabin roof and seatback top edges, I decided to clean up the transom while I was at it.

Again I used the sander as a grinder to remove most of the epoxy and excess ply, and then switched to finish sanding to complete the job.

In this pic you can see the before (starboard) and after (port) halves of the transom.


And here is the finished article.


You can also see that I have shaped and smoothed the big fat fillet on the outside of the boat where transom and transom skirt are joined.

That was fun!

Seatback Tops | Trimming To Size

When the seatback tops had cured I set about trimming off the excess material inside and outside the boat.

Again the marking device shown in the build manual came in very handy. Here is it is use.


Then I used the Japanese saw to remove most of the excess from both outboard edges.

Experience gained from trimming the cabin roof made this a quick and easy task.

The inboard edges were a little trickier.

There is nowhere to start a saw cut inside the boat, so I drilled a couple of entry holes and used a keyhole saw to remove enough waste to fit in a saw. Like this.


That allowed the Japanese saw to be deployed to cut out most of the excess material. As here. 


This was straightforward. A chisel was required to chop away the excess at each end.

Then, as with the cabin roof, the sander was used in rotary mode with a P40 grit to grind away what waste remained before switching to random orbital mode and P60 and P80 grit to clean up the inboard and outboard edges.

Here are both seatback tops trimmed, seen from astern.


She is starting to look like a capable little boat!

Transom Skirt Fillet

I had been putting off making a fillet across the transom where it is joined to the transom skirt.

But now I had to do it, so I could move on to other more enjoyable things.

I knew the first application would turn out horrible, and it did. Here it is.


Absolutely awful. So I got out the drill and a carbide burr, and dressed it to remove most of the rough stuff.

It looked a little better after that.

Finally, I sanded it some more and taped it up for the second layer which will turn it into a much more respectable fillet. Like this.


That's it for now!