Monday, 12 October 2020

Seatback Tops | Installation

With the roof trimmed to size it was now time to fit the tops to the cockpit seatbacks.

This was a straightforward exercise.

The tops were securely buttoned down with plenty of temporary screws and epoxy resin, being careful not to apply too much glue in way of the seatback locker tops where squeeze out could make a nasty mess.

I installed the port side first, using plenty of glue.

When satisfied that it was tightly held down by all the screws I scraped off all the flash on the outside.

Then I carefully scraped off and wiped away any epoxy on the upper inside edges of the locker. To do this you need to be able see inside the locker - doing it by feel alone will just make a mess. Here is my secret weapon for doing this.


It's an old bicycle mirror, used with a couple of small, bright lights to see into each corner of the locker. It works really well.

Lastly I pulled the blue tape from inside the locker.

Here is a view of the port seatback top from the stern.


I repeated the exercise on the starboard seatback.

This is what both seatback tops looked like when installed, seen from astern.


With the roof and seatbacks in place it feels like we are really making inroads to this build!


Cabin Roof | Trimming To Size

When the cabin roof had fully cured I set about trimming off the excess material around the edges.

But how to know exactly where to cut it?

It was then that I realised the real value of a marking tool shown in the build manual. This is what it looks like.


I made it from a piece of scrap ply. You merely slide it along the side of the hull and mark in where the point at the top aligns with the roof. Simple!

Having marked out its outline I then roughly trimmed the roof to get rid of most of the excess material.

Here is a view from the front of the port Dorade box area.


I had to drill entry holes to use a jig saw across the forward face of the cabin.

Otherwise a Japanese saw made light work of cutting all other edges.

Further trimming was done with the Rotex 90 sander set to rotary mode and using a P40 grit, turning it effectively into a grinder to remove most of the remainder.

Lastly I switched to using the sander in random orbital mode with a P60 and then a P80 grit to get to the final finish.

Here is the roof with its finished trim, viewed from the front on the port side.


Lastly, here is a rear view of the starboard side.


Looking good!


Seatback Tops | Getting Ready For Installation

 While the cabin roof was curing I prepared the seatbacks for installation in the same way that I had done in the cabin.

The only area in the seatbacks where squeezed out glue would be a problem is inside the lockers, so I taped the edges of the locker tops. This is the port locker top.


You can see that all the edges are protected by blue tape and plastic sheeting. The bottom of the locker is also covered with plastic dust sheeting to catch any drips.

The starboard locker received the same treatment, like this.


My plan is to reach inside the lockers when the tops are in place and scrape off the squeeze out before pulling the tape. We will see how effective that is in due course ...


Cabin Roof | Installation

When all the preparation was complete and all tools and materials standing by ready for use, I went ahead with the permanent installation of the cabin roof.

It went well, with little or no drama.

Here is a view from starboard of the roof glued in place and firmly buttoned down with plenty of temporary screws.


This is another view from the port side.


You can see that the roof is quite considerably oversized at the front, almost as if the original design had a longer cabin but the roof panel was left unchanged!

It's no matter - it is actually very reassuring to know that there is plenty of waste material around the perimeter.

The temporary screws into the carlins in the hatchway were insufficient by themselves to hold the roof down tightly, so I added some spring clamps to assist. As here.


That did the job nicely.

When all the screws and clamps were in place I cleaned up the squeezed out epoxy on the outside, and then hopped into the cabin to do the same inside.

Lastly, I pulled out all the blue tape which was protecting the interior of the roof and the Dorade boxes from squeeze out. It worked really well, as this pic of the port roof shows.


Luckily I took photos before the glue had cured, when I noticed that a strip of blue tape was still in place. So I quickly peeled it off.

This is a view of the starboard roof inside the cabin.


An this is the view looking forward.


The cabin will be entirely white inside, and will look very smart indeed!

Next job is the seatback tops ...

Friday, 25 September 2020

Seatback Fillets

It was time to make the fillets for the seatbacks, where they meet the rear cabin wall, deck and transom.

Two factors would impact how this progressed.

First, these are the most visible fillets in the entire boat and if they are not just right everyone will see it immediately. No compromise on quality can be made here.

Second, making fillets is my least favourite activity on this build. Nothing about it could be described as enjoyable, as readers of previous posts will know. So I was reconciled to not having fun for a few days ...

As always I mixed up a good quantity of wood flour fillet mix, and applied a generous bead all around the seatbacks. I made a bespoke filleting tool to get a nice wide fillet on the deck.

As always it cured like roughcast concrete, spiky as a porcupine.

Here is the first fillet on the starboard side.


It looked absolutely horrible. But I knew it would and was ready to apply two or more layers to get a good finish.

So, as always I dressed the fillets with a carbide burr in a powerful corded drill, and sanded them by hand and with a sanding machine. See previous posts for more detail, if you're curious about this awful process.

This is what the starboard fillets looked like afterwards.


Still horrible but ready for a second layer to make the fillets of equal width and to improve the surface.

Here the starboard side is taped up ready for a second layer.


And here is it is with the second layer in place.


It looks quite a bit better, but after it was dressed and sanded it still clearly needed a third layer for final fairing. I expected this from previous experience, so no surprises here.

Once again I taped up the fillets for the third layer, and this is what the port seatback looked like after application.


Much better. I haven't sanded this yet but it looks like it will turn out nicely. Any minor blemishes or holes can be faired with phenolic glass balloon mix. The key is to make sure the fillets are of even width and really smooth to receive their fibreglass cloth cladding.

Onwards and upwards ...


Cabin Roof & Dorade Boxes | Getting Ready For Installation

In readiness for fitting the cabin roof I used a lot of blue tape to make cleaning up the squeezed out epoxy resin as easy as possible, and to make less mess.

First I taped up the sheerclamps, carlins and cleats in the cabin. Like this.


The inside of the Dorade boxes were similarly taped up, and protected with some plastic dust sheet material. As here in the port box.


There is piece of old cloth in the bottom, in case of drips.

Lastly the cabin roof itself was prepared with lots of blue tape, like this.


You can see that I painted the roof inside the Dorade boxes, because I thought it would be a lot easier than trying to do it later.

I found that using tape like this was an effective way of achieving clean joints when fitting the cockpit deck panels. In this instance it should be easier because I won't be laying on my back underneath the deck, with epoxy dripping into my hair!

Let's hope so ...



Seatback Tops | Making & Test Installation

The seatbacks were ready for their tops to be fitted.

The build manual calls them 'decks', which I think is a bit grandiose for a strip of plywood 3" wide, so I will stick with 'tops'!

The first task is to trim the panels to the correct length. The panel is held in the correct position with a couple of bits of stiff wire in pilot holes while the ends and the sides are marked in with a pencil. Like this.


The ends are then easily trimmed with a saw and a block plane, as here.


The location of the sheerclamp and the upper seatback stringer are then pencilled in and holes for the temporary screws are drilled.

The stringer is quite flimsy so I used 3.5 x 25mm screws, with plywood washers to prevent damage to the panels. The screws are at 6" intervals.

The panel is then put back in place and the locations of pilot holes for the screws are marked in and then drilled. 

The panel is then test fitted using all the temporary screws to check for a good fit, as seen here from the front of the boat.


And here is a view of the starboard panel from the stern.


Lastly I had to drill holes for the boom gallows stanchion poles. The holes were marked in with a pencil from inside the seatback lockers and the panels were transferred to the bench for drilling.

Here is the port panel with the hole marked in. It is exactly the same size as a two pence coin.


This is a large diameter hole and has to be drilled with a Forstner bit, so freehand drilling was a bad idea. I used the drill guide and my small cordless drill, set to low speed for maximum torque. Like this.


And here is the hole drilled out. A piece of scrap ply is underneath the panel to protect the bench and the drill bit, and to prevent tear-out in the panel.


Lastly I made one final test fit to check the alignment of the holes. Here is the port panel in place.


And here is the starboard seatback top.


All was well so the panels were set aside to await installation.