Saturday, 7 November 2020

Fibreglass | Topsides & Seatback Tops

The build manual suggests that it might be easier to 'glass the front and rear topside panels (fore and aft of the cabin topside area) when the boat is upside down.

I can't see how that would be a good idea, when it is an easy task to cover the entire upper hull with 'glass cloth all in one go.

So that's what I did.

First the overlaps from the cabin roof and topside panels were sanded and feather edged to accept the additional topside panels.

Here is the starboard overlap onto the rear panel, nice and smooth.


And here is the starboard overlap onto the forward panel. Again, nice and smooth.


Patterns for the topsides were made by laying paper along the panels and scribing in the curves and overlaps.

This is the rear topside pattern taped in place for a test fit on the port side.


And this is the pattern for the forward topside panel, taped in place on the starboard bow.


Next the patterns were taken inside the house to cut the 'glass panels. There isn't any room in the workshop to do this.

Here the patterns are held firmly in place on the rolled out cloth by a couple of stuffed chicken door stops. They work well, and don't talk back.


While marking out the cloth for each rear topside panel I added an overlap of 15cm to the top edge, so that the same piece of cloth will cover the seatback top and overlap down the seatback into the cockpit.

Here I am marking in the overlap on the 'glass cloth.


 I just use a rule to mark the cloth 15cm away from the edge of the paper pattern.

Then as always the cloth is cut just inside the marks to get a correctly fitting 'glass panel.

Here is the rear topside 'glass panel fitted and held in place on the starboard side, ready for wetting out.


And here is the forward topside 'glass panel clipped in place on the starboard bow.


Clear resin was then applied with a disposable roller to wet out all the panels.

This is the forward panel on the port side.


And this is the rear panel, again on the port side viewed from the front.


In the following pic you can see where the topside 'glass panel extends across the seatback top and overlaps down onto the seatback itself, in one seamless layer.


I carried the inside overlap down to the top edge of the seatback locker openings.

And finally here are the the newly covered topsides, seen from port at the stern.


Looking good!

Fibreglass | Footwell

The sides of the footwell had been half covered by fibreglass cloth overlaps when the cockpit was 'glassed.

It remained for the footwell sole and the bottom half of the sides to be covered.

Again, it was easy to make a pattern and be sure that the 'glass panel would fit correctly.

I measured the footwell and made a scale drawing of the 'glass panel required to complete covering it, including overlaps where necessary.

Here is the drawing.


The measurements were transcribed onto a full size paper pattern which was then used to cut out a 'glass panel.

Here is the footwell after the panel had been installed and wetted out.


Every time I look at that footwell it seems just a bit too narrow for comfort, but it is what it is ...


Fibreglass | Rear Cabin Wall

The rear cabin wall is not a complex shape but it is a large area with long right angle edges in the companionway, so a pattern was required.

It was easy enough to measure the panel and transcribe its shape to a paper pattern, as here.


The big aluminium roofer's square is ideal for marking out large right angle joins.

This is the pattern, clipped in place for a test fit.


The overlaps from the cabin top were sanded and feather edged, as here.


And lastly the 'glass panel was fitted and wetted out, like this.


Progress is good!

Fibreglass | Forward Cabin Wall & Dorade Boxes

Unlike the cabin tops and cockpit deck, the forward cabin wall is a complex shape and a pattern is required if we are to cover it with a single piece of 'glass cloth.

So I measured the various panels that comprise the forward cabin wall and Dorade boxes and marked them out on a paper pattern. I also scribed in the curve of the cabin roof.

This is the paper panel on the bench.

It was a good fit in the boat, as here.


A panel of 'glass cloth was cut using the pattern and dry fitted to the cabin wall, like this.


 Finally it was carefully wetted out with clear resin, working from the top down and centreline outwards to stop the cloth from falling onto the deck. It went well and looked like this.


Wetting out is satisfying because it covers a large area very quickly!


Fibreglass | Cockpit Deck

Time to 'glass the cockpit deck.

After some pondering I decided to used a single full width sheet of cloth laid down the centre of the cockpit, leaving a small area on each side to be covered by overlaps from the seatbacks.

I would also be able to have a generous overlap down into the footwell.

In this way I could cover almost all the deck with a single piece of cloth, with no overlapping seam along the middle.

First I removed the cardboard covers that protect the watertight locker interiors. As here.


I laid some plastic dust sheeting in the locker bottoms, to catch any epoxy drips. Like this.


Then I laid a sheet of cloth in the cockpit, cutting for overlaps onto the transom and the rear cabin wall and down onto the footwell sides. It looked like this.


Like the cabin tops and topsides, minimal measuring and cutting were required.

Finally all was wetted out with clear resin and left to cure. Here is the front view from port.


We're getting there!


Fibreglass | Cabin Roof & Topsides

When the fillets were all smooth and ready for 'glass I laid a sheet of cloth on each side of the cabin roof, overlapping onto the topsides and across the chine onto the lower hull.

Here is the cloth laid out on the cabin top, Dorade box and topside on the port side.


I cut nice wide overlaps all around.

Here is the same side viewed from the rear.


The humble wall paper brush is the best tool I have found for smoothing the cloth into place. It doesn't snag or catch the weave.


The same process was carried out on the starboard side of the boat, as here.


This was quite straightforward, with very little cutting to get neat overlaps on the front and rear cabin walls.

A full width sheet of cloth was used and allowed to fall down over the chine onto the lower hull sides.

The cloth was then wetted out with a disposable roller. This is the view from port at the front of the boat.


Note that I have cut away the top of the cradle support arms to allow the cloth to overlap the chine.

And here is the same side viewed from the rear.

Lastly, here is the view from starboard at the front of the boat.


There are generous overlaps all round.


Finish Sanding Fillets

Before any fibreglass fabric could be applied to the upper hull, all the fillets would have to be made smooth to receive the cloth.

Sanding was tedious but straight forward, mostly carried out with the 90mm random orbital sander fitted with a soft sanding head so it could follow the contours of the fillets.

Here are the finished fillets in the cockpit and on the rear cabin wall.


And here are the transom and footwell fillets.


 Time to cut 'glass!