Tuesday, 11 February 2025

Gloss Paint | New Conditioner & 6th Coat

As expected the fifth coat was an improvement on the fourth but was still not nice enough for the 'show coat'. I was still getting brush and lap marks, and wanted to avoid this as far as possible.

I mentioned in the previous post that I found a gold mine of useful tutorial videos on the Off Center Harbour website. The third of three 'how to varnish' videos really sang the praises of Epifanes Easy Flow paint conditioner. The tutor said it was 'like magic' and she always used it when varnishing.

So I got some. It can be used with any traditional or synthetic single part paint or varnish. This is it.


I obtained a small glass measure so I could accurately administer a small dose, if needed.

And this is our paint.


The fifth coat was wet sanded with a P400 grit in readiness for the sixth and final coat, as recommended by Epifanes. This takes a long while but is worth it for the excellent surface which results.

Here we are wet sanding blue gloss on the port side.


Good lighting is essential.

And here we are wet sanding white gloss on the starboard bottom.


When feathering the joins between white and blue paint I did sand through to primer in some places, so some touching up was required. Like this.


The touched up patches were then wet sanded when cured, to blend in with the rest of the surface.

The undersides were then masked up, firstly for white gloss. The sixth coat was applied and the tape pulled.

This was allowed to fully cure for a week before the hull was masked up for blue gloss, and again the sixth coat was applied and the tape pulled.

For this coat I didn't use any thinners or hardener, but instead I added 10% Easy Flow conditioner.

It worked really well, especially on the blue paint.

This is the starboard side.


And here is the transom.


It looks really good!

The paint flowed out really well on the sides and on both blue and white stripes. The bottom panels aren't quite so nice, but they will be out of sight and will get abraded anyway, so I'm not going to worry about it. It is certainly not worth another coat.

I will be using Easy Flow from now on. The sides and the stripes have no brush or lap marks, and from a couple of yards away you would think it is a spray finish.

Repainting the undersides has been a trial but I have learned so much and I am confident the topsides will turn out well.

I will now allow the blue paint to cure before varnishing the transom and rub rails.

That feels like progress!


Gloss Paint | New Tape & 5th Coat

Well, it's been quite a while since my last post. The Christmas festivities took up a lot of time, as usual, and we have had a lot of work done in the house which has meant I have not been able to spend much time boatbuilding.

However, I have not been completely idle.

In the previous post I had finished applying the fourth coat of white and blue gloss on the undersides of the boat. This coat was thinned with 10% Epifanes thinners and had 5% AwlGrip hardener added.

I didn't really expect it to be the final coat, and of course it wasn't. Brush and lap marks took care of that!

So the whole undersides of the boat were wet sanded with a P400 grit until it was beautifully smooth all over, and then masked for white gloss.

Now, since the previous post I have done a lot of research into masking tape and paint conditioners.

I found a mother lode of great advice at the Off Center Harbour website. You will have to join to access their tutorial videos, but it's worth it.

There are three excellent videos on how to varnish a wooden boat, and the second one is all about masking tape and how to use it. As a result I invested in some 3M 218 Fine Line tape, as used and recommended by a professional boat painting shop. This is it.


It comes in various widths. I am using 1/2" for long straight or slightly curved sweeps, and 1/8" for tight curves. The 1/2" tape doesn't like tight bends - it buckles.

This is the transom masked up for white gloss.


I have to back up the 218 tape with ordinary masking tape because it is only 1/2" wide.

This is the transom masked for blue gloss.


And this is the starboard side masked off for blue gloss.


The fifth coats of both white and blue gloss were applied, thinned with 10% Epifanes thinners and with 5% AwlGrip hardener added.

I was hopeful that this might be the final coat, but not really expecting it to be so. I left it for two weeks to fully cure.

See the next post for the outcome!


Tuesday, 3 December 2024

Gloss Paint | Progress

It's been a while since the last post. I have been trying to resolve my paint problems, with mixed results.

The initial prognosis was that I did not wait long enough for the paint to cure before masking up for the next coat, causing the tape to damage the underlying gloss when pulled.

The paint vendor sent me a sample of some hardener to help the paint cure faster and harder. This is it.


It's called Topcoat Brushing Converter, from AwlGrip. I was advised to add 5% to the gloss, which I did in a test which worked.

However, the same problem reoccurred when I pulled the tape on the fourth coat of white gloss on the hull. The tape tore off the blue paint, like this.


This was discouraging, to put it mildly.

I concluded that it must be the tape itself that was the problem. Throughout the build I have been using 3M 471 vinyl tape. This is it.


Another builder on the PocketShip Forum told me that he used 3M 244 Gold tape to successfully paint his boat.

I did some research and found that the vinyl tape has an adhesive strength of 25 units, whereas the gold tape only has 2 units.

Clearly I was using the wrong tape!

I bought some 244 Gold tape. Here it is.


A fourth coat of blue was applied to the bottom, sides and transom, using this tape.

This was the result.


No damage at all!

The Gold tape doesn't provide the precise edge that I get with the vinyl tape, and there is a very small amount of bleed.

But I can live with that. It is a small price to pay for getting the boat painted.





Tuesday, 29 October 2024

Gloss Paint | Hiatus

As mentioned in the previous post, I contacted the vendor (BoatPaint) and they confirmed immediately that I had not left the paint long enough to cure.

Apparently the mono-urethane needs a week to fully cure. It doesn't say that anywhere in the product information or instructional videos...

But at least I now know what the problem is.

The downside is that instead of taking ten days (say, two weeks) to apply five coats of both colours, it will now take ten weeks.

It's time for a gin and tonic and some jazz.


Nothing else is going to help at this point.

Gloss Paint | 2nd Coat of White & Disaster!

The time came for the second coat of white gloss, so I taped up again. Like this.


And here is the rear view.


I applied the second coat of white and then removed the masking tape.

That was when it all went wrong... the tape removed large amounts of the blue gloss it was adhering to, leaving patches of bare primer. Like this on the port quarter.


This happened all around the boat. Here is the bow.


Something was seriously amiss. I wet-sanded the damaged areas with a P400 grit to restore a smooth surface, like this at the bow.


And like this on the starboard quarter.


I thought I might have applied too much paint, thereby preventing the solvents from evaporating.

The unused paint remains liquid for days afterwards. Here is the roller tray several days later, showing how fluid it still is.


I also thought I may have not left enough time between coats, and that could be why the first layer was not cured.

I resolved to contact the vendor for advice.


Gloss Paint | 1st Coat of Blue

I had previously decided to apply the blue and white contiguously, a layer at a time rather many layers at once. This was designed to avoid having a significant physical 'step' between the two colour blocks.

So the next task was to tape and mask for blue gloss.

Here is the transom, ready for gloss.


The first coat of blue was applied.

Here is the view from the front of the boat.


And here she is with the tape removed.


The paint covers really well and flows out beautifully, leaving no brush marks and no dry edges. As with the white gloss, I found that adding 10% thinners helps a lot with application.

Lastly, here is the transom with tape removed.


Looking good!


Gloss Paint | 1st Coat of White

We left the previous post with the boat ready for the first coat of white gloss.

I thinned the paint with 10% Epifanes thinners, and rolled it on and tipped it out with my favourite brush.

Here she is.


And here is the transom.


This is the view from the front with tape removed.


And again here is the transom, without tape.


The finish is OK, but not amazing. I found it very difficult to keep the wet edge, and it shows. Although I think that might be due to a lack of experience on my part.

But it covers well and flows out very nicely, leaving no brush marks.

We're on our way!