Tuesday, 3 June 2025

Paint Blisters | Another Test

If you have been following this build for the last couple of years you will be aware that all the white paint on the boat blistered when exposed to water (i.e. rain) when it was moved onto its trailer late in 2023.

Nobody, including the paint manufacturer, could tell me why. But I eventually worked it out.

At least I think I did...

The technical instructions for the paint tell us to use the manufacturer's own specific thinners to clean brushes and rollers.

I didn't do that. I used a water-based brush cleaner. I meticulously cleaned my brushes and rollers with this stuff, and reused them time and time again.

In doing so I am sure that I impregnated them with whatever solvent is in the brush cleaner, and they in turn contaminated the paint.

When the paint became wet the water caused the contaminant to reactivate, blistering the paint.

It only affected the white paint. The blue paint was fine, so it's clearly something in the white gloss that is intolerant.

I decided to test my theory while there was still plenty of the old paint on the boat, and poured a few cups of water into the forward deck well.

I left it overnight, and sure enough all the paint covered by the water had blistered.

Here is a close up pic of the blisters.


Horrible!

Here is another pic with a ruler for scale.


You can see that the blisters are tiny, but can you imagine what the boat would look like covered in a rash like this?

I can, and that's why I am repainting with Epifanes!

Friday, 16 May 2025

Topsides | Paint Strippng

Work at last began on stripping the topsides paint. I am using the same techniques, tools and materials that I deployed on the undersides, so see previous posts for detailed descriptions if interested.

Here I have started work on the port cockpit deck and sides.



I think it will be a lengthy but relatively straightforward process, so I'm not too concerned about making progress at this stage.

The Centreboard Now Drops!

When we moved the boat back onto its build cradle I took great pains to make sure it was located where the build manual says it should sit, which is with the centreboard slot exactly between the two cradle end pieces.

As a result the centreboard now drops to the floor, which it never did before. This indicates that it was too far to the rear of the cradle the last time we did this.

Here is the board touching the floor.


This is useful to know, because I can easily touch up a couple of dings on the forward edge of the board before putting her on the trailer.


Getting Ready For Paint Stripping

Before any paint stripping could take place in the cockpit it was necessary to ensure no stripper could drip or leak into the interior or onto the transom.

So I used plastic sheeting to seal up any vulnerable areas.

Here the lazarette hatch openings and the rudder slot have been covered up.


Both drain holes in the footwell have been plugged with BlueTack, like this.


Lastly the companionway, ratchet block support pad and centreboard pendant were sealed off, like this.


We are now ready for stripping!

Making The Keel Support Block

I needed to support the keel at the stern of the boat so that I could safely work in the cockpit. Otherwise it could tilt under my weight, which would not be good.

So I made a support block. Here it is.

Some foam padding glued in place with double sided tape prevents damage to the paintwork.

It is now safe to work in the cockpit.


Paintwork Protection | Plastic Sheeting

Having spent a lot of time and trouble repainting the bottom of the boat I had no wish to splash it with paint stripper when stripping the topsides.

I used plastic sheeting to protect the paint. Here is a view of the port side.


And this is the transom.


I have only taped the sheeting to the rub rail and to itself to form a curtain around the boat. No tape is in contact with new paintwork since previous experience tells me that tape always leaves a mark, however faint. And we don't want that!

The sheeting is not in contact with the paint work either, so it can't abrade the surface.

The primary purpose of the sheeting is to protect against splashes of paint stripper, but it also plays a secondary role in preventing damage by accidental contact. Which is not unlikely, given that the garage is in frequent use by the other member of the household … 


Ratchet Block Support Pad | Removal

The next item for removal was the main sheet ratchet block, attached to its support pad.

I had previously removed the machine screws which secured the pad to the deck, so it was simply a matter of separating the pad which was now only held down by caulk.

I used a long, sharp, thin-bladed knife to slice through the caulk. Taps from a mallet assisted greatly. This is the loosened pad.


That was easy.

Lastly, the centreboard pendant cleat was removed, leaving the topsides ready for paint stripping.