Friday, 16 May 2025
Ratchet Block Support Pad | Removal
Lazarette Hatches | Removal
The hatches came away without too much trouble but it was immediately obvious that I had the same problem that I experienced with one of the portlights - the caulk had hardened excessively and was not easily removed.
Sunday, 4 May 2025
Flipping The Boat (Again...)
There were a few tasks to complete before turning her right side up. One very important one was to make sure that the centreboard pendant was pulled in completely and cleated off.
It was easy to raise the board a few inches while Mrs Boatbuilder pulled the pendant through and tightened it. She retrieved about two feet of rope which would have allowed the board to drop down out of the keel when the boat was turned over, which would have been a big problem.
Sunday, 27 April 2025
We're Ready to Flip the Boat!
This close up shows the heavy-duty braked castor wheels that I used on the build cradle so I could safely and easily move the boat around the workshop.
Friday, 25 April 2025
Cabin Interior | Repainting
It was time to apply paint inside the cabin.
I thought I had used a quality paint the previous time but I was advised by a professional decorator that it wasn't that great.
So this time round I chose the best I could find. This is it.
It is Dulux Trade brilliant white eggshell for interior use, solvent based.
I first painted the stringers and carlins with a brush, to see how the paint felt.
It was very thick and hard to apply straight out of the tin, so I asked the Dulux people if I could thin it.
The rather grumpy lady who runs the store said to use white spirit but no more than 10%, or I would "destroy the integrity of the paint". Now, we don't want that to happen, do we?!
A test with 5% white spirit added to the eggshell caused the paint to flow very nicely, so that's what I did for the entire repaint.
I used the same roller sleeves that I used with the Epifanes yacht paint, by Rota. They are excellent. This is them.
Two rollers were needed, with a long and a short handle. Here they are.
Two coats were applied and at time of writing seem to have done the job.
This is the centreboard case, seen through a porthole.
And this is the roof.
I will see what it looks like when dry but I am really pleased with how this turned out.
Now I need to organise the boat flipping crew …
Postscript
Having said that I was happy with the paint, a close look the following day revealed that there were still some small patches where the eggshell had not fully covered patches where I had sanded through the old paint to the substrate.
The Dulux eggshell claims to be "Self Undercoating", so I didn't bother to prime these patches. I should have known better!
So a third coat was applied and it looks much better now. Sometimes I have to remind myself that perfectionism is not my friend …
Cabin Interior | Preparing For Repaint
It was nearly time to flip the boat upright again, but before I did that I decided to repaint the interior.
The white paint had turned yellowish and no longer looked smart. It would be much easier to refresh inside the cabin while the boat was upside down, so that's what I did..
The first task was to lightly sand all the old paint. My Festool sander was too big to use inside the boat, so I looked around for a small cordless palm sander.
The smallest I could find that were up to the job were all 125mm, and I opted for the DeWalt random orbital sander simply because I already had a charger and two batteries that I could use to power it.
This is it.
It comes with a dust collection bag but a trial proved that it was ineffective and still created a lot of dust, so I connected it to my vacuum cleaner with a conical connector, like this.
Some tape prevented the connector pulling loose from the sander. As here.
This was a very successful modification. I could now sand most of the interior with minimal dust creation.
I taped the floorboard and centreboard case edges and around the inspection hatches to mask them off.
Here is the centreboard case.
This is the inspection hatch in Bulkhead 2.
And here are the floorboard edges.
Then I sanded as much of the cabin that I could reach with a P80 and then a P120 grit.
I could easily reach most of the cabin with the sander, but the storage compartment and the transom were out of reach.
So I made a sanding tool by taping a sheet of medium grit nylon abrasive pad to a long handled roller arm. This is it.
This was very effective in lightly sanding impossible to reach places.
Inevitably I sanded through the paint in some places. This is one in the corner of the roof.
I am hoping that two coats of a quality paint will suffice to cover everything. We will see!
Friday, 18 April 2025
Build Cradle | Reassembly
When we moved the boat out of the workshop onto its trailer I dismantled the build cradle.
I put the two cradle ends behind my workbench and put the spreaders and support blocks in the scrap pile.
I did consider scrapping the cradle ends but thought if I ever needed to put PocketShip back inside for rework I would need them, so I kept them.
That was a very sensible decision, because we will soon need another build cradle when we flip her upright again!
The spreaders had long since been cut up and recycled so I made a new pair. Here I am cutting them to length.
I searched through all of my many boxes of scrap and found all the support blocks from the original cradle.
Here are the new spreaders and the old blocks.
I drilled the spreaders for screws using the pillar drill to ensure the holes were perpendicular, like this.
Then I took all the parts outside and stood the cradle ends on a pair of tables.
All parts were marked up to ensure they were correctly reassembled, like this.
I carefully screwed all the pieces back together, using a big roofing square to make sure everything was at right angles.
This is the reassembled cradle.
I will fit the wheels when we flip the boat.
Lastly I removed the spreaders and put the parts safely back inside.
That was fun!